How to build a simple deck?
How to do custom deck construction? We have discussed here a simple deck construction method that you can follow to build a deck.
Step1. Attach the laser
First, locate the top of the laser and snap a level chalk line. Cut 2 inch wide, 1½ inch thick treated wooden speakers for every 2 feet length and aligns the top of each spacer with a chalk line and fastens with 6D nails. Now align the trench with the top of the spacers and nail the wall of each spacer with a 16D nail.
Step2 Protect the laser
Fold the membrane along its centerline to make an angle and apply it over the laser-to-home joint so that one foot covers the spacer block and the top of the trench, and the other foot extends to the wall. Now fold the metal to form a right angle. Apply it on the waterproof membrane and run the nails over the roof with the top edge of the flashing every 8 inches.
Step3. Set Footings
Dig a hole in each foot so that it is deep enough to hold the ground form and extend below the snow line. Now assemble the foot parts as per the manufacturer’s instructions and collect the hole forms one by one in each hole.
Step4. Install post base and side rim joist
Place a post base on top of the pier and position it so that it does not interfere with the joist hanger and mark its position. Now remove the post base and replace the post base with a hammer drill. Then insert an anchor bolt and tighten with an impact wrench.
Step5. Install front rim joists, beams, and interior joists
Attach the concealed-flange double zest hangers to the inner 2x end of the front rim joist and fit the inner 2x s to the post base. Fit the side rim joist on the front hanger and post with the nails on the front rim joist 2x post hanger. Now drive 16D nails at the end of the side rim joist with the mouth of the front rim joist and repeat the same with the rim joist on the other side.
Step6. Attach trim and decking
Finally, measure the outside distance of the walls and trim board and add 1 inch for overhang. Then cut the deck boards according to the length. Continue gluing and nailing until the deck is complete and replaces the house siding within 1 to 1 inch of the decking.
Different deck construction cost
It costs $ 2,200 to build a 10x10 foot deck and, 8,800 to build a 20x20 deck. However, the cost of different decks can be different depending on the type. You can contact the deck builder near you to get free estimates before you build the deck. Below are some deck construction costs discussed:
1. Pressure Treated Deck Cost
Pressure-treated wood decks cost 12$ to 18$ per square foot. In the United States, about 75% of the pressure-treated wood is used. Chemically treated in this pressed wood, which is fabricated to make the wood more resistant to mold, insects, and rot.
2. Wood Deck Costs
Making decks with this natural wood costs 3$ to 15 per square foot, and most homeowners spend an average of 6$ to 8$ per square foot. The wooden decks are much more beautiful to look at, making it one of the top choices of homeowners, but it requires more maintenance like staining and sealing.
3. Redwood Deck Cost
The most commonly used natural wood for deck construction is Redwood, California. It costs 15 to $ 21$ per square foot for a redwood deck, and about 7$ per square foot for materials is a little more per square foot than redwood pressure-treated wood.
4. Cedar Decking Cost
Cedar decking per square foot costs 4$ to 8$. Cedar is natural softwood that is offered either with or without treatment. Most of the time, these planks are left untreated due to weather resistance.
5. Composite Decking Cost
The composite decking cost 23$ to 38$ per square foot. Most homeowners spend 5,821$ and 10,826$ to build a 12 x 24 combined deck with railings. This recyclable combination looks like real wood, and its popularity is growing in deck building materials.
How to find a Contractor to Build a Deck?
Are you looking for a deck construction contractor? This is not a very difficult task. You can easily find a good contractor. Below are some sources for finding a deck builder:
Friends: The easiest way to find a decking contractor is to get information from friends. If any of your friends have done deck building work before, they will be good at it and will be able to help you find a contractor.
Angie's List: One can find a single contractor from Angie's list, as it is a good source for sorting contractors with former client ratings. Angie's list is a category where you have to pay in advance.
Deck Company: There are currently many deck companies from which you can get deck building services. If you search online, you will find many types of deck building companies that will provide you with all the information, including cost.
The bottom line
We've talked about the cost of building a custom deck and the source of finding a custom deck construction. If you are looking for a good contractor to build the deck of your home, follow the sources shown by us. Also, let us know if you have any further information about the deck contractor, and we will do our best to help you.